Factory directly provided Air Circuit Breaker-FTW1 for Suriname Manufacturers


Technical data

Product illustration

Tripping characteristic

Exterior and dimensions

Related video

We rely upon strategic thinking, constant modernisation in all segments, technological advances and of course upon our employees that directly participate in our success for Factory directly provided Air Circuit Breaker-FTW1 for Suriname Manufacturers, Our professional technical team will be wholeheartedly at your service. We sincerely welcome you to visit our website and company and send us your inquiry.


This video from Sears PartsDirect shows you what to do if your electric dryer won’t start or run. Several things could keep your dryer from operating normally. You could have a blown thermal fuse, which can happen if your vent hose has a buildup of lint. You could also have a bad door switch, a defective start switch or an issue with your power supply. This video shows a few easy tests you can run, including how to use a multimeter to check for continuity between these parts and locate which component is causing the problem.

Visit us at:


Or call 1-800-437-1673 to speak with a parts specialist.

The video includes these parts and tools. Look up your model to make sure you get the right parts for your dryer.
Door switch


Thermal fuse


Start switch




Find parts for your dryer at:


Or click here to schedule an appointment with a repair technician. https://www.searshomeservices.com/repair#showall

Hi, this is Wayne with Sears PartsDirect. Today, we’re going to troubleshoot and electric dryer that won’t start. If your dryer won’t start, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. First, let’s rule out a power issue. Open the dryer door and check if the light inside the dryer turns on. If it doesn’t turn on, check your power cord and the house circuit breaker. Try resetting the breaker to make sure it’s not tripped. Once you’ve confirmed that the dryer is getting power, with the dryer door closed, set a Timed Drying cycle and listen for the faint sound of the timer motor running inside the console. If the timer motor runs and the light comes on when you open the door, you know that the door switch is okay. You can skip ahead to the next segment where we’ll show you how to check the thermal fuse and start switch. If not, we’ll check the door switch with a multimeter next. For safety always make sure the power is disconnected before you check continuity. To access the door switch, pull out the lint screen. Remove the screws that secure the lint screen housing to the top panel. Release the clips and lift the top panel to access the door switch. Unplug the door switch from the wire harness. With the dryer door closed, put your meter leads on the door switch wires that connect to the blue and white wires on the other end of the plug. You should measure near 0 ohms of resistance. If you measure no continuity, on this meter that’s an “OL”, then the door switch is broken and needs to be replaced. Here’s a video that will walk you though that process. The next thing we’ll check is the thermal fuse. With the dryer unplugged, remove the screws and pull off the back panel. Unplug the wires from the thermal fuse. Use the multi-meter to measure the resistance between the spades on the thermal fuse. You should measure near 0 ohms of resistance through the thermal fuse. If you measure no continuity, then replace the thermal fuse. Here’s a video showing you how. Here’s something to keep in mind. More often than not, if you blew a thermal fuse, it’s because your exhaust vent is clogged with lint. Before you hook your dryer back up, check your vent and clean it out with a lint brush. Now, if your thermal fuse was okay, the next thing we’re going to check is the start switch. Reassemble the dryer and then plug it back in. Open the door and push the door switch in. While holding the door switch in, push the start switch. You should hear a click as the relay engages. Then release the door switch and you should hear a click as the relay disengages. If you heard the clicks, the start switch is probably okay. If you didn’t hear the clicks, let’s check continuity on it. With the dryer unplugged, remove the console back panel. Unplug the wires from the start switch. Have someone hold the start switch in and check resistance on the spades for the light blue wires. You should measure near 0 ohms of resistance with the start button pressed in. If you measure no continuity, then you’ll need to replace the push-to-start switch. Here’s a video for you. If all of the components have checked out ok then the motor windings or internal centrifugal switch could be defective. You should get a qualified technician to check this out. Hey thanks for watching. Check out our other repair videos here on the YouTube channel, and if you like them, subscribe.

GameBreakerGod DBZ creative combo artist

Related Products

WhatsApp Online Chat !