Factory Price Miniature circuit breaker-FTM8-LE Supply to Vietnam


Technical data

Product illustration

Tripping characteristic

Exterior and dimensions

Related video

we can offer high quality products, competitive price and best customer service. Our destination is "You come here with difficulty and we give you a smile to take away" for Factory Price Miniature circuit breaker-FTM8-LE Supply to Vietnam, We welcome customers, business associations and friends from all parts of the world to contact us and seek cooperation for mutual benefits.

Product illustration:

Technical Data

Model FTM8LE Residual current circuit-breaker
Number of poles IP+N,2P,3P,3P+N,4P
Rated frequency: AC 50/60Hz
Rated voltage (V) AC 230/400
 Rated current (A) C D 1,3,6,10,16,20,25,32,40,50,63 1,3,6,10,16,20,25,32,40,50,63
Rated residual operating current(mA) 30
Rated residual non-operating current(mA) 15
Residual current breaking time 30mA≦0.1s  250mA≦0.04s
Rated short-circuit breaking capacity(KA) 6(In≦40A); 4.5(In﹥40A)
Rated residual current breaking capacity(KA) 3
Mechanical & electrical life: 10,000 operations
protection rating Ip20
Installation On DIN rail 35mm according to JB6525
Connection capacity: Cross-section of conductors up to 25mm2
Tightening torque 2 Nm
Ambient temperature (°C) -5°C ~ +40°C
Altitude (m) ≤2000m
Relative air humidity no more than 95%
pollution degree
installation condition Used in place without obvious shock and vibration
 Weight (g) ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A
216 240 320 343 445 473 468 518 585 63

Exterior and dimensions



 Number  of poles Rated current
<40A ≥40A
Width (mm) Modules Width(mm) Modules
1 /2 45 2.5 54 3
2/2 63 3.5 72 4
3/3 90 5 103.5 5.75
3 /4 99 5.5 117 6.5
4/4 117 6.5 135 7.5

SR-H Remote Racking Controller – GE AKD-5/AK-25 Circuit Breakers

The Safe-T-Rack (STR) SR-H remote racking controller, which racks the General Electric AKD-5/AK-25 breakers, is designed to be used with all horizontally racked medium voltage circuit breakers. The STR SR-H: properly stimulates all of the OEM breaker interlock systems; does not interfere with existing manual racking systems; and comes with an impact- and moisture-resistant polymer storage case.

And as with all Safe-T-Rack products, this model is simple to install and use, and is proudly made in the U.S.A.

Visit http://www.safe-t-rack.com/products for more information.

Safe-T-Rack… Because distance is the best arc flash protection.


Today we'll be doing a review of how to install the Camco Power Grip Replacement RV Power Cord Plug with Handle in the 30 amp in the made end, part number CAM55245. Now to change out this plug on your existing power cord or extension cord by 30 amp RV style plug, all you'll need is a razor knife to trim back the outer coating, phillips head screwdriver, take out the screws, as well as tighten down these, as well as tightening down the inner screws and a pair of wire strippers to strip back the installation on the internal wires before you make your connections inside here. It will take about 5 minutes and you can have your plug changed. Here's our cord, it would be the end that would plug in to our trailer, our camper and this is the end that you plug in to your outlet at your campsite, your 30 amp 125 volt. If this end was damaged, Camco has a replacement for it, it is a 30 amp male end or 125 volt for your camper, so your cord would not be a complete waste. You could simply cut the end of this off and you'd have to strip back some of these outer coating, so you expose the wires, you'll have a green, a black and a white wire in there. For purposed today though, we're not going to cut this one, this is actually still a good cord, but if this end was damaged, this replacement would actually go on here. We'll go ahead and go over how you would wire this new plug. Let's go ahead and you'll need a small phillips head screw driver.

Note: Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.

Related Products

WhatsApp Online Chat !