Good User Reputation for Miniature circuit breaker-FTM8-LE for Cyprus Factory

Overview:



Technical data

Product illustration

Tripping characteristic

Exterior and dimensions

Related video

Our company insists all along the quality policy of "product quality is base of enterprise survival; customer satisfaction is the staring point and ending of an enterprise; persistent improvement is eternal pursuit of staff" and the consistent purpose of "reputation first, customer first" for Good User Reputation for Miniature circuit breaker-FTM8-LE for Cyprus Factory, We sincerely welcome domestic and foreign merchants who calls, letters asking, or to plants to negotiate, we will offer you quality products and the most enthusiastic service,We look forward to your visit and your cooperation.


Product illustration:

8-LE
Technical Data

Model FTM8LE Residual current circuit-breaker
Number of poles IP+N,2P,3P,3P+N,4P
Rated frequency: AC 50/60Hz
Rated voltage (V) AC 230/400
 Rated current (A) C D 1,3,6,10,16,20,25,32,40,50,63 1,3,6,10,16,20,25,32,40,50,63
Rated residual operating current(mA) 30
Rated residual non-operating current(mA) 15
Residual current breaking time 30mA≦0.1s  250mA≦0.04s
Rated short-circuit breaking capacity(KA) 6(In≦40A); 4.5(In﹥40A)
Rated residual current breaking capacity(KA) 3
Mechanical & electrical life: 10,000 operations
Installation
protection rating Ip20
Installation On DIN rail 35mm according to JB6525
Connection capacity: Cross-section of conductors up to 25mm2
Tightening torque 2 Nm
Ambient temperature (°C) -5°C ~ +40°C
Altitude (m) ≤2000m
Relative air humidity no more than 95%
pollution degree
installation condition Used in place without obvious shock and vibration
 Weight (g) ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A ≦32A ﹥40A
216 240 320 343 445 473 468 518 585 63

Exterior and dimensions

8-LE111

 

 Number  of poles Rated current
<40A ≥40A
Width (mm) Modules Width(mm) Modules
1 /2 45 2.5 54 3
2/2 63 3.5 72 4
3/3 90 5 103.5 5.75
3 /4 99 5.5 117 6.5
4/4 117 6.5 135 7.5




Disclaimer: This video is to show the way I did the job of upgrading my 10/3 feeder wire. I am not showing the way all the experts watching would do it. I am a licensed aircraft avionics (electrician) not a home electrician:I did not cut a long opening in the drywall. This sub-panel was inspected by an electrical underwriter back in 1985. Now I am wiring my new workshop with an existing sub-panel I had installed back in 1985. I am a licensed aircraft technician and was allowed by the town code board to wire my own one family house wiring, including connecting to the incoming power company wiring that terminated on a pole connected to my house, this was back in 1985, I do not think that is allowed anymore.Now I am updating the size to 10/3 coming from the sub-panel to the underground UV cable I had buried back in 1985. The two 30 amp switches I have been using, although renewed, could be eliminated and just use the sub panel circuit breakers when your not using shed power, also I am installing an 8 foot copper rod, pounded into the ground and connected to the shed box neutral bar using unshielded solid # 4 copper wire with the required rod clamp. The main house neutral bar is also connected to a #4 solid copper ground wire unbroken to the pipe below the house’s main water shut off valve and continues out of the house and connected to an 8 foot copper rod with heavy required clamp.This gets pounded below the dirt close to the foundation. Over 616 HD Video



This range of “No Hole” circuit breaker lockouts are ideal for breakers that do not have any built in locking facility. The unique design, with thumb wheel operation clasps onto the switch providing secure locking protection. Can be used with lockout cleats below for hard to lock longer sliding switches and switches with large angular rotation.

CB09 Fits switches 16.5mm wide x 11.6mm thick (usually up to 277 Volt)

Related Products

WhatsApp Online Chat !