OEM Factory for Miniature circuit breaker-FTB10LE Supply to Swiss

Overview:



Technical data

Product illustration

Tripping characteristic

Exterior and dimensions

Related video

We believe that long term partnership is a result of high quality, value added service, rich experience and personal contact for OEM Factory for Miniature circuit breaker-FTB10LE Supply to Swiss, We are confident to make great achievements in the future. We are looking forward to becoming one of your most reliable suppliers.


 

Model:   FTB10LE
Poles: 1P+N
Rated current (A): 6,10,16,20,25,32,40
Rated frequency(Hz): 50
Rated operational voltage(V): 230
Breaking Capacity:Ics(KA) 4.5
Rated residual operating current:A/AC: 30
Breaking time:A/AC: 15
Breaking Time ms : I△=I△n ≤100
I△=5I△n ≤40
Mechanical and electrical life: 10000
Conventional non-tripping current:   t≤1h
Conventional tripping current: t≤1h
1s<60s
 Instantaneous tripping types: C
 Instantaneous non-tripping current: 5In
 Instantaneous tripping current: 10In
Connecting Wire: 1/25
Size(L×W×H)mm:   74.2×36×80

 





  • There are several things that could be keeping your oven from heating. Even if the lights on your oven light up, you could have an issue with your 240-volt power supply. But you could also have a bad bake element, electronic control board or a break in the wires between the two. This video will show you how to use a multimeter to check for continuity between these parts and locate which component is causing the problem.

    Visit us at http://www.searspartsdirect.com?sid=soc:youtube:oven-wont-heat-troubleshooting-gas-range-problems

    Or call 1-800-437-1673 to speak with a parts specialist.

    The video includes these parts and tools. Look up your model to make sure you get the right parts for your range.
    Multimeter

    http://www.searspartsdirect.com/part-number/82141/0034/034.html?sid=soc:youtube:direct-part-link

    Electronic Control Board

    http://www.searspartsdirect.com/part-number/316630004/0022/628.html?sid=soc:youtube:direct-part-link

    Bake Element

    http://www.searspartsdirect.com/part-number/316206000/0022/628.html?sid=soc:youtube:direct-part-link

    Find parts for your range at:

    http://www.searspartsdirect.com/partsdirect/product-types/Range-Parts?sid=soc:youtube:card-range-parts

    Or click here to schedule an appointment with a repair technician. https://www.searshomeservices.com/repair#showall

    Transcript:
    Hi, this is Wayne from Sears PartsDirect. Today, we’re going to talk about troubleshooting an electric oven that won’t heat. The first thing we need to do is confirm that we have 240 volts of power going to the oven. You may think that your oven is getting enough power if the controls light up. An electric oven needs 240 volts to heat, but only 120 volts to operate the controls. Even if these work you, could still have a power source problem. Let’s see if we’re getting any heat on the surface burner. That will tell us whether we’re getting 240 volts or not. If the surface burner doesn’t heat, check your house circuit breakers for the range. One of the two circuit breakers could have tripped, which could be the reason your range is only getting 120 volts. Reset both circuit breakers and check for heat now. If you’re still not getting heat, you could have a problem with your power socket. Now, if the surface burner heats, you definitely have the 240 volts of power to the range. Our next step is to unplug the range and the check continuity through the bake element. Always disconnect power before checking continuity. Remove the upper back panel. Unplug the element wires from the electronic control board. Measure the resistance through the yellow and orange wires that go to the bake element. Your meter should read about 16 ohms of resistance through that circuit. If you measure around 16 ohms of resistance, then the bake element circuit is okay. Remove the lower back panel. Check the continuity of the red wire between the terminal block and the electronic control board. Your meter should read near 0 ohms of resistance through that red wire. If so, the electronic control is getting the 240 volts needed to heat the element, it’s just not sending it to the heating element in the bake mode. In this case, you’ll need to replace the electronic control board. This video will show you how. Now, if you read no continuity, when you checked the bake element from the control board, then you probably have a broken bake element or a wiring failure in that circuit. Check the resistance of the bake element directly at the element terminal ends. If your meter reads “OL,” replace the bake element. This video will show you how. If you measure about 16 ohms of resistance through the bake element, then you know you have a break in the wiring between the electronic control board and the bake element. Check the continuity of the wires between the electronic control board and the bake element to find the break. Repair or replace any broken wires. Take a look at this video to learn more about repairing broken wires. Hey, thanks for watching today. Check out our other videos, here on the YouTube Channel, and don’t forget to subscribe.



    Distribution board wiring light indicators for single phase and 3 phase 4 wire system, light indicators wiring diagram explanation in Urdu/Hindi video tutorial.

    Related Products

    WhatsApp Online Chat !