Wholesale 100% Original XJM7-J Measuring box (Infrastructure Energy Measurement Box) for Washington Factories

Overview:



Technical data

Product illustration

Tripping characteristic

Exterior and dimensions

Related video

We not only will try our best to offer excellent services to every customer, but also are ready to receive any suggestion offered by our customers for Wholesale 100% Original XJM7-J Measuring box (Infrastructure Energy Measurement Box) for Washington Factories, We sincerely welcome both foreign and domestic business partners, and hope to work with you in the near future!


USE:

XJM7-J metering box (infrastructure power metering box) is suitable in power supply system with AC 50HZ, rated voltage 380 / 220V , as the power measurement in construction site.

 

Meet GB7251.1-1997 and GB7251.3-1997 standards.

3C certificate:

XJM7-J Mgy Measurement Box)-2





Intermatic’s Occupancy/Vacancy Sensors provide lighting automation at your fingertips, allowing for energy efficiency. In today’s video learn how to properly install your Intermatic 2-circuit In-Wall Occupancy/Vacancy Sensors. This instructional video is intended for all IOS-DDR Models.

No neutral wire is required, making it perfect for retrofit applications.

Everything you need for installation is inside the box:
• Decorator wall plate
• Wire connectors
• The switch

To ensure accurate performance and safety please be aware of the following advisories:
• Avoid transparent barriers, such as glass windows
• Do not mount directly above a heat source or in an area where hot or cold drafts will blow directly on the sensor
• Ensure no objects are blocking the sensor’s field of view

For your convenience, the instructions for the video can be found below:

Step 1 – Disconnect the power at the circuit breaker or disconnect switch.

Step 2 – Take out the old switch.

PRO TIP: You should have two wires plus a ground wire (which is the no neutral) and two additional wires for in and out. This is how you know the DDR is the right replacement switch.

PRO TIP: In this application, the two yellow wires are for the second button. Make sure you know what is in your LINE/HOT, POWER IN, or LOAD/POWER OUT before connecting the new switch. If you aren’t sure, please contact an electrician.

Step 3 – Remove ¾ of an inch of insulation from the end of each circuit conductor on the sensor switch. Make sure the ends of the wires are straight.

Step 4 – Connect the lead wires.
• Black to Orange with Black for LINE 1/HOT
• Red to Orange for PRIMARY LOAD wire
• Blue to Yellow with black for LINE 2/HOT
• Brown lead to Yellow for SECONDARY LOAD
• Green to Green for GROUND

HINT: When you have two wires with a ground or no neutral, the ground wire MUST be connected for the unit to operate.

Step 5 – Use a twist-on wire connector to join one supply conductor with one 16 AWG device control lead.

Step 6 – Gently position the wires in the wall box and fasten the switch. Make sure the switch is mounted TOP up.

HINT: Two control switches control two loads on this model.

Step 7 – Move the band switch to adjust the switch’s operation:
• You can select the Occupancy Dual Mode (OCCD) setting to automatically switch both loads ON or OFF after the set time delay.
• Slide the band to the center position to select the Occupancy Single Mode (OCCS). This setting enables automatic ON and OFF after a set time delay for your primary load.
• Your primary switch is the button on the left.
• On the right, Vacancy Dual Mode (VACD), also known as “Manual ON Occupancy Mode,” sets the switch for manual ON and automatic OFF after the set time delay.

Step 8 – After selecting the mode you want, replace the small cover plate and install the designer wall plate.

To learn more about Intermatic Sensors, please visit: http://www.intermatic.com/sensors

Connect with Intermatic online:
Like Intermatic on Facebook: https://www.facebook.com/intermaticinc
Follow Intermatic on Instagram: https://www.instagram.com/intermaticinc
Follow Intermatic on Twitter: https://twitter.com/intermatic
Follow Intermatic on Google+: https://plus.google.com/+IntermaticIncorporated
Follow Intermatic on Pinterest: https://www.pinterest.com/intermatic
Follow Intermatic on LinkedIn: https://www.linkedin.com/company/intermatic



Chinese authorities for the first time close the Shanghai and Shenzhen stock exchanges early under a “circuit breaker” mechanism to curb volatility after shares fall seven percent.

Related Products

WhatsApp Online Chat !